Materials

Ferrous metals

Thermomechanically strengthened high-strength reinforcing steel of the 1000 MPa class for prestressed reinforced concrete.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Tin babbitt of ГОСТ 1320 with cadmium and nickel for poured linings of plain bearings under high speeds and dynamic loads: high- and medium-speed diesel engine bearings, crosshead bearings.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Cast lead-tin bronze for plain bearings with high surface pressure and edge loading: vehicle, rolling-mill and calender bearings, piston-pin and gearbox bushes, thrust washers.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Cast lead-tin bronze that runs well with little lubricant or water lubrication, for bearings with strong edge loading, cold-mill bearings and piston-pin bushes; resists sulphuric acid.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Cast high-lead tin bronze with the best sliding properties of its group, for fast-running bearings: grinding machines, water pumps, cold and foil rolling mills, composite engine bushes.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Cast leaded tin bronze for plain bearings with high load peaks: crank and toggle bearings, piston-pin and crane-wheel bushes, spindle nuts, heavily loaded slide plates; seawater resistant.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Cast leaded gunmetal, a medium-hard plain bearing material with good emergency-running properties, for bearing bushes and sliding parts; seawater resistant.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

ГОСТ cast tin-lead bronze for bimetallic plain bearings.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

ГОСТ cast tin-free lead bronze for antifriction parts: plain bearing shells and bushes.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Cast leaded tin bronze, a soft sliding material with 8-10 % lead, for bearing bushes and plain bearings.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Heat-treatable free-machining Al-Cu-Pb-Mg alloy for automatic lathe parts, screws and nuts: short chips, relatively high strength; contains 0.8-1.5 % lead, not for food contact or fusion welding.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Heat-treatable free-machining Al-Cu6 alloy with bismuth and lead, the classic automatic lathe alloy for turned parts, screws and fittings; not for fusion welding.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Heat-treatable free-machining Al-Cu4-Pb-Mg alloy with strength near 2017A for turned parts, screws and nuts; contains 0.8-1.5 % lead, not for fusion welding.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Non-heat-treatable Al-Mg2.5-Cr alloy of medium strength for sheet metal parts, tanks and welded structures with good corrosion resistance; suitable for food contact.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Non-heat-treatable Al-Mg4-Mn-Cr alloy close to 5083 with better resistance to sea atmosphere and good toughness at low temperature for shipbuilding, chemical plant and welded sheet structures.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Heat-treatable Al-Si-Mg structural alloy of medium strength for complex extruded profiles of railway cars, buses, masts and welded frames; better suited than 6082 for decorative anodising.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Heat-treatable weldable Al-Zn4.5-Mg1 alloy of high static and fatigue strength for loaded welded structures, rail vehicles and military equipment.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Heat-treatable high-strength Al-Zn5-Mg3-Cu alloy for tooling plate, plastic injection moulds, machine building and machined parts; not for fusion welding.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Commercially pure aluminium 99.0 % with high thermal and electrical conductivity and formability for sheet metal parts, cladding and food-contact ware.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Non-heat-treatable Al-Mn1 alloy for sheet metal parts, cladding and containers, also for food contact: stronger than pure aluminium and easy to form.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Secondary Al-Si8-Cu3 casting alloy of EN 1706 with good castability and strength at elevated temperature for general-purpose castings in sand, permanent moulds or under pressure.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Commercially pure 99.0 % aluminium of ГОСТ 4784 for sheet, strip, plate, profiles, bars, tubes and wire.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Non-heat-treatable Al-Mg2 alloy of ГОСТ 4784 of medium strength, weldable without restriction, for sheet metal parts, tanks, tubes and welded structures.

Properties, analogues, sources, notes and hardness need a paid account.

Non-ferrous metals

Heat-treatable Al-Zn-Mg alloy of ГОСТ 4784 for extruded profiles, bars and large tubes and for non-welded structures in construction, machine building and aircraft.

Properties, analogues, sources, notes and hardness need a paid account.